PureXIII
Members-
Posts
40 -
Joined
-
Last visited
-
Feedback
0%
Profile Information
-
Gender
Male
-
Location
Sydney
Profile Fields
-
Car(s)
370z
Recent Profile Visitors
2,140 profile views
PureXIII's Achievements
-
Aftermarket Pedders Springs - Manufacturing date on label says 2011/12 as show in pictures. Not sure on spring rates, sits slightly lower than stock. Good for clearing rego/defects Have since sold my skyline so they have to go Pickup from Richmond NSW 2753 Inspection welcome Can post in NSW for about $50, Interstate for approximate $100 (will get a quote if required) Sold as is Link for more pictures http://www.ebay.com.au/itm/152023407517?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
-
PureXIII started following R34 Gtt Inner Splash Guards. Complete Set , For Sale: Clean R34 Gt-t [nismo Lmgt 4s] {nsw} , R32 Gtr Clutch On R34 Gt-t? and 5 others
-
Okay i've confirmed the clutch is a 6 button pull type off the R32 GTR and as far as I know from what i've read all 34 GT-Ts are pull type. So the question is will it fit?
-
Just wondering if a 32gtr clutch and flywheel would fit in a 34 gtt? Only asking because my neighbour as a pretty much brand new 32gtr button clutch which is isnt using since he sold his car. Don't really want to take off the gearbox and housing just to find out it dosn't fit.
-
Definitely a guard roll on the front, back might be okay(no roll) but will probably poke out a lot. Also those tyres will be stretched on the front.
-
I had 9.5 +38 test fitted on the front without a tyre and it was touching the suspension on full lock. 8.5 +30 fits perfect, no guard rub no guard work, normal tyre. 9.5 +30 will probably be quite close to the suspension especially on full lock but it may just fit. However it will poke out and may need guard work not to rub. Maybe rota does custom orders?
-
9.5 + 35 probably wont clear the inner suspension on the front. You would probably need to go for a much lower offset if you want 9.5 on the front.
-
Might be a bit tight on the front. I couldn't fit 9.5 +38 on the front it was too inset and was hitting the suspension strut. I went for ; 8.5 +30 on the front 245/40 9.5 +38 on the rear 265/35
-
Decided on selling my Cuga's as they are just too small. Here is the thread if anyone is interested
-
This listing is for a PAIR of Bride Cuga *STYLE* Seats Bought through the group buy on SAU. Reason for sale: Selling as they are slightly too small for me (due to my wide back 51cm shoulder to shoulder - see position C in the photo) Condition: Brand new Seats come with universal rails* Back of seat is made from black Fiber Reinforced Plastic (FRP) Seats are reclinable Measurements: A - 25cm B - 52cm C - 46cm D - 50cm E - 31cm F - 53cm G - 34cm H- 82cm Bottom Seat depth - 42cm Made in China by Wujiang Jianwu FRP co. LTD *Please note these are high quality replica seats - not original bride's Local pickup is preferred - Richmond NSW 2753 Payment: Cash on pickup, paypal, direct deposit Link to original group buy Ebay link with more pictures
-
Replacing Headlight Globe - Hid Or Halogen?
PureXIII replied to PureXIII's topic in General Maintenance
Finally ended up getting the globe out. You do need the torx screw driver(T20) as "central cost person" said (it prevents the cap from turning) Figure out you need to turn the ballast connection anti-clockwise to unscrew it. (from this thread guide) Also ballasts were underneath the housings - seeming to be intact, no wiring cut. This is my bulb I'd Assume the Philips Xenon Vison D2R is the replacement right? -
Replacing Headlight Globe - Hid Or Halogen?
PureXIII replied to PureXIII's topic in General Maintenance
Does this mean i still have the factory Xenon HID ballasts and they weren't remove at compliance (or re-fitted after)?