-
Posts
85 -
Joined
-
Last visited
-
Feedback
0%
Profile Information
-
Gender
Male
-
Location
Perth
Profile Fields
-
Car(s)
Skyline R34
-
Real Name
Salah
Recent Profile Visitors
4,183 profile views
6BANGER's Achievements
-
PeepTehToad started following 6BANGER
-
R32 Gtr Long Term Love, Now Project
6BANGER replied to r32-25t's topic in Projects, Overhauls and Build-ups
I would to ask a few questions about this os88 issue . Did you end up fixing the oil spitting out of the breather hose issues? -
R34 GT with Neo Engine - No Speedo
6BANGER replied to 6BANGER's topic in Drivetrain and transmission
I will try to test it with a Nistune ECU as soon as I get a hold of one. In the mean time, I was hoping its a matter of running a direct feed someone to by pass this issue -
6BANGER started following GT3076r, 6boost, PWR FMIC, Plazmaman, PowerFC, R34 rear seats , R34 RB25DE to DET conversion , R34 DE+T with R33 gearbox, R34 auto loom - speedo? and 1 other
-
R34 RB25DE to DET conversion
6BANGER replied to Scottyp's topic in RB Series - R31, R32, R33, R34 (1986-2002)
I have the same issue and been losing hair everytime I take another look into it. I can understand the frustration Here is what I have tried so far... 1. Run a wire from the speed sensor in the gearbox to the cluster and ECU 2. tested for continuity between ABS computer and cluster (speed signal wire) - all ok 3. tried a second hand cluster that was working at the time 4. used self diagnostics and got the following codes (26 - 44 - 46 ) -
R34 DE+T with R33 gearbox, R34 auto loom - speedo?
6BANGER replied to Pr0x1mity's topic in Drivetrain and transmission
I also tried running a wire directly to the ecu. didnt work either -
R34 DE+T with R33 gearbox, R34 auto loom - speedo?
6BANGER replied to Pr0x1mity's topic in Drivetrain and transmission
I got a 25Det NEO installed in a R34 GT and lost speed signal. I checked the gearbox and found the black and brown wires that run to the speed sensor. Question is, where abouts on the cluster do I need to run this wire to? I have already tried running a direct wire from the brown on the speed sensor to pin 19 on the back of the cluster which didnt work. I can confirm there is nothing wrong with either the sensor or cluster so its down to a wiring issue. -
Before we get into it, I have been searching the entire Internet and the R34 manual for the past week without much luck. Now, here is the problem. I have a R34 GT which came with a RB26 engine setup for RWD. It also came with the RB26 loom and ECU. This Everything worked well along with the R33 gearbox. After building the RB26, I decided to swap the motor with a RB25det NEO engine, gearbox, loom and ECU. Yes, this is when the speedo stopped working. I have traced the issue down to the TCS/ABS ecu as the GT (NA) ECU does not have TCS but the GTT ECU is now looking for a signal from the TCS. Here is what I have tried so far... 1. Run a wire from the speed sensor in the gearbox to the cluster and ECU 2. tested for continuity between ABS computer and cluster (speed signal wire) - all ok 3. tried a second hand cluster that was working at the time 4. used self diagnostics and got the following codes (26 - 44 - 46 ) 2 of them related to TCS/ABS The golden question is How can I get my speedo to work again???
-
Yes, the left wheel speed sensor is connected in the engine bay. However, the wiring loom near the ECU uses different connectors between the GTR and GTT. I was hoping someone can shed some light into how the GTT body loom can be connected to the GTR ECU.
-
Hey mate did you end up doing the engine swap? I have a R34 GTR RB26 in my GTT and currently running the RB26 engine loom and GTT body loom just like you mentioned. Engine starts and drives but I have the ABS light on due to the left wheel speed sensor.
-
RB25 NEO Plazmaman plenum and throttle body $1000. Garrett gt3076r, 6boost mani, hoses/lines, exhaust dump with wastegate flange $2,500. RB25 Neo PowerFC inc boost controller value and hand controller $1000. PWR front mount and piping, blitz bov, z32 afm with plug $750. Also have 1000cc injectors (unsure of brand) with fuel rail and plug in loom and sard regulator for $750 This is a complete 400hp bolt on kit that will save you the cost of fabrication. All Located in Perth, WA
-
I'm looking for a 60mm genuine Defi link meter bf oil pressure gauge, sensor and wiring. Prefer model df04401 which the White light version 0417796179
-
Skyline R32/r33/r34 Parts
6BANGER replied to 6BANGER's topic in For Sale (Car parts and other accessories)
Wastegate is 44mm and not 38. 1 sold and 1 left Drift wing sold Twin pipes exhaust sold Turbo kit sold Mono steering wheel sold R34 cross over pipe. Sold