Butters

Seems bang on to me , g30-900 will make 900 crank on e85(on paper). Deduct ~25% for 98 and you are at 675 crank. Run that to the wheels and fact you are only running 26psi you end up about your number. People forget how magic E85 is now that just about everyone is running it. "Back in the day" you had to be north of 30psi on a 850+hp turbo to get 600 at the wheels on 98.

I've never seen this on a factory built RB26 have the screws come out, or gears break for that fact. Only once someone has touched the motor have I heard / seen it. I've seen a few factory built Rb25's shatter gears but we talking high mileage extreme beating at drift track, constant limiter for a full season. Well outside what it was built for.

Over the moon in fact. Engine is coming out to put on a new enlarged sump. I planned on putting on either a new pump(Tomei / Nitto) or billet gears. But a bit of waste of time if the crank has narrow collar. Things spiral quickly, if crank is out, new bearings ... maybe new rods and pistons ... wait just rebuild the engine... oh but I should get an N1 block .... 40k later .... haha.

THANKS ! Sequential at times but overall Incremental is probably a better way to state it. Chassis numbers with Nissan's are like that too, jump when a change of some kind occurs. Bit of a surprise to find out that despite being a 32 RB26, it's most likely the better crank. Winner Winner.

found this on the forum , suggests I am in the range ----------------------------- From the segmented (potentially incorrect) information I've found that; Early R32: RB26000XXXX to RB26002XXXX Mid R32: RB26003XXXX (V-Spec I RB26-03XXXXX - Reference Classic Register) Late R32: RB26004XXXX (V-Spec II RB26-042XXXX - RB26-045XXXX - Reference Classic Register) Early R33: RB26005XXXX Mid R33: RB26006XXXX (as per the engine in this R32 V-Spec II, which is what I'm concerned about from legitimacy perspective) Late R33: RB26007XXXX Early R34 (2000+): RB26008XXXX ----------------------

Now as I understand it the engine numbers are sequential for the rb26. EG stamped - RB26040100A is a 40,100 engine. Now they made between 1988 and 1994 43,834 R32 GTR's In 1994 they made 7,464 r32 gtr's. So if you have a ~37,000++ number RB26 it's "safe" ish to assume its an 1994 motor and a long nose crank ? The long nose crank being introduced somewhere in Feb of 1993.

I've read that before, really good article. However my ~900hp+ at flywheel, means it can be done. Also have tested it with one pump on only, does what you'd expect, near 700's flywheel. No disagreement that i will have horrible pressure drop compared to what it would be on a bigger lines. I can also overwhelm the regulator / return line at low HP consumption with both on, but I don't do that, so no issue So horribly inefficient but it works really well for the 10 seconds or so the second pump is on.

So what did you end up doing ? and is it still alive today ?

I run 2 x 525 pumps on factory 8mm fuel lines ... zero issues, staged of course Your setup should work fine, all you need to do is find the restriction. A good aftermarket fuel regulator is always a good idea too. If it's not your regulator i'd be suspicious of your fuel tank breather and your tank pressurising. Next would be something with the fuel hat. Then blow out the fuel lines.

Clearly this is just a "ME" problem

For some reason I find myself removing the rear diff often. The top two back bolts that go into the diff to hold the attesa pump in place are just a PAIN. Has anyone mounted the attesa pump to the subframe instead of diff ? Also thinking about trying a stud on one of them to help locate. Other idea's ? or tricks ?

Yes Rb26 I am using an Ignite 5.0 bottom/crank trigger on the ATI and will be doing the same on the ROSS. On one setup I have VCAM so using that sensor as the top/cam trigger. *cough Toyota style ... *cough On the other I am using an Ignite 5.0 cam trigger. I also use link ecu too, so once you get sync, the ecu runs completely off the crank. You can literally unplug the cam sensor once started. I get zero trigger issues and drive the car weekly.

36-2 balancer is the biz. Personally prefer it over a gear with teeth. I run an ATI 36-2 custom wheel on my street car as it has Aircon Putting a ross 36-2 on my race car, no AC. I'll look up the company that did the ATI if your interested, sit down price though

If you want a 4inch muffler check out SP Mufflers. After some advice I got on here I reached out to them. Made me 2 custom mufflers in 4inch in and out to suit my probably one of the few Cefiro with 4inch exhaust. Super easy to deal with and it is super quite, maybe too quite. They can make to suit you though. https://www.instagram.com/spmufflers/

It's always been my policy but I have no comparison motor without one to compare it to. As others have said, the one on your motor is also for sure trashed by now.