Jump to content
SAU Community

Aftermarket Parts Galore!

toy515
 Share

Recommended Posts

toy515 Grand Master

toy515

Posted
Posted

Aftermarket parts galore

Greddy intercooler kit r32 r33 r34 $220

Splitfire coilpacks s2 rb25 $300

Mahle forged pistons rb25 rb26 $380

Manley forged rods rb25 rb26 $200

Velo fixed back racing seat with rail to suit skyline $250

Exedy heavy duty clutch with flywheel rb20 rb25 rb26 only a month old $150

Hardrace adjustable rear camber arms r33 r34 s14 s15 $120

Varex cat back exhaust s14 s15 missing controller $200

Tommy kiara strut brace r33 r34 $150

Tomei gear knob $40

Tein Coilover spanners $30

Custom catch can $20

52mm autometer boost gauge $30

52mm autometer air fuel gauge $50

52mm speco water temp gauge with sender $30

60mm autometer boost gauge $30

S15 eyelids $60

Turbosmart fuel cut defender $40

Turbosmart boost tee $30

Red tow hook $20

S15 air diversion panel $40

R32 3 inch front pipe $20

R34 3 inch stainless front pipe $30

S15 3 inch front pipe $20

Gtr stainless front pipe $80

Apexi turbo timer $30

Greddy turbo timer $30

Blitz turbo timer $20

Hks turbo timer $20

Nardi boss kit $50

Gold Coast

0487924497

Link to comment
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • portaz
      Walbro 460 in r32 gtr

      By portaz · Posted

      I disconnected before the fuel pump and restriction still there. Disconnected at turbosmart fpr and also after ethanol sensor and pressure dropped. No kinks in line but I found one spot above diff that I can hear the fuel flowing while running so I'm wondering if there is built up corrosion  from 10 years of sitting.  I had injectors cleaned and tested and one was dead but rest were fine. Was never an issue when I owned the car previously but I'll talk to jez about his thoughts on if they should be changed to newer tech. Thx guys at least I know the setup should work again. Pump is wired directly to relay and not using factory plug any  more 
    • robbo_rb180
      R32 Gts+t Daily/street

      By robbo_rb180 · Posted

      Nice work on the shroud/ducting.  
    • ELFGT350
      Newbies

      By ELFGT350 · Posted

      Hi and best of luck with your car. Its a bit hard to tell how low the car is all round from that pic or if its been lowered or not. 90mm is a bit low on the front apron but it depends on the shocks & springs condition & whether or not its been lowered. Going to 19” wheels will give you 15-20mm depending on rubber but you might need new shocks. Mine -2005 are weeping fluid slightly but have lasted 19years!!. So if yours are original they need replacing anyway if they havent been touched before.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Hi everyone, Recently got handed down a 2004 Skyline 350GT Coupe. I would like to change the wheels as the previous owner installed some weird ones. The current ones are 215/45ZR18, unsure of the offset, and sit pretty deep in. Would like to increase the ground clearance slightly as well as I need to get it roadworthy standard, currently sitting at 90mm. Was thinking that maybe I could kill 2 birds with 1 stone by getting new wheels.  Pictures of current wheels: https://imgur.com/bg1QMIu Any recommendations for the types of wheels I should be on the lookout for? Like the maximum and minimum offset, sidewall height, width, etc.  Sorry in advance if I'm noob, I do not know much about cars other than how to change the oil, a blown tyre and brakepads....
    • Lvonn1
      RB25DE Rebuild tolerances

      By Lvonn1 · Posted

      Hey MinKer, Where abouts did you get that table from ? 
×
×
  • Create New...