Jump to content
SAU Community

R34 Manual Conversion In Melb?


Charles89
 Share

Recommended Posts

Just want to know if anyone knows a place in SE melb that does pretty cheap yet decent manual conversions?

And does anyone know for sure how much a conversion will cost? Include parts and labour?

Also, has anyone dealt with Advanced Jap Auto Imports before? They quoted me $350 for the conversion labour, which sounds too cheap to be true for me :)

Link to comment
Share on other sites

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Charles

I could not give you a price

But i know a few that have had conversions done at RE Customs and there happy with the work and price

So i would go and see Ray at RE.

Link to comment
Share on other sites

$350 is toooooo cheap. thats how much im paying for labour to get my clutch changed lol

alot more work is involved. as Wayne mentioned speak to the boys at RE

you also have status tuning also and both work shops are highly recommended.

Link to comment
Share on other sites

$350 is toooooo cheap. thats how much im paying for labour to get my clutch changed lol

alot more work is involved. as Wayne mentioned speak to the boys at RE

you also have status tuning also and both work shops are highly recommended.

Yea, 350 sounds so dodgy lol, but a couple of other workshops has quoted me about $1000 for labour.

I tried calling Ray today but he wasn't in, so I'll try again on monday ;)

Link to comment
Share on other sites

$350 is insanely cheap. Maybe they were thinking parts only or something?

As someone said, $1000 sounds more in the ballpark. If it's too expensive, may be cheaper to just sell your car and get a manual one lol

Link to comment
Share on other sites

$350 is insanely cheap. Maybe they were thinking parts only or something?

As someone said, $1000 sounds more in the ballpark. If it's too expensive, may be cheaper to just sell your car and get a manual one lol

Well yea.... The only reason why I'm considering about it, is that I found a awesomely straight & clean auto R34 GTT (66,000km) for $14,000. So if I buy it then convert it to manual, it will still be cheaper than a manual R34 with low k's. But after having a hard think about it, I don't think its worth all the trouble and headaches, so now I'm thinking to import one.

What do you guys think?

Link to comment
Share on other sites

i recently done a manual conversion thanks to O.H Performance. they're located westside. completed within a week. parts came off a low km's r34 half cut that they supplied, new excedy 5 puck brass button clutch and labour came to the $4000 mark. got quotes elsewhere ranging from $5000-$6500 parts+labour. very happy with the work the boys did, have had no problems and they were straight out honest.

Link to comment
Share on other sites

i think theres some cheap manual R34 GT-T's so buy one of them, one recently sold for as low as 13k, it was stock but still prices are dropping

Wow....13k?..... You sure it wasn't a N/A? lol

The cheapest 34 GTT I saw was about 17k with like 120,000km+ on the clock :)

i recently done a manual conversion thanks to O.H Performance. they're located westside. completed within a week. parts came off a low km's r34 half cut that they supplied, new excedy 5 puck brass button clutch and labour came to the $4000 mark. got quotes elsewhere ranging from $5000-$6500 parts+labour. very happy with the work the boys did, have had no problems and they were straight out honest.

That's pretty good, I got quoted $3500 for the whole conversion using R33 parts. How did your conversion go? Did you have to re-tune it? Was there anymore money spent after the $4000 you spent on the conversion?

Link to comment
Share on other sites

nope nothing else, all the interior plastics were supplied, even gearknob. of course cluster and steering wheel are still auto items. conversion is awesome, gearbox was in good nick no crunching gears or anything, clutch was gone though so replaced with a 5puck brass button excedy clutch. no tuning necessary, the boys dealt with all the electricals.

Link to comment
Share on other sites

nope nothing else, all the interior plastics were supplied, even gearknob. of course cluster and steering wheel are still auto items. conversion is awesome, gearbox was in good nick no crunching gears or anything, clutch was gone though so replaced with a 5puck brass button excedy clutch. no tuning necessary, the boys dealt with all the electricals.

Sounds alright, but I still think paying 18k for a manual GTT is better of paying 14+4k for a manual converted GTT.

What would you do if you were me? :)

Link to comment
Share on other sites

Sounds alright, but I still think paying 18k for a manual GTT is better of paying 14+4k for a manual converted GTT.

What would you do if you were me? :)

if i were you i would go for this http://www.skylinesaustralia.com/forums/Eo...tt-t276944.html its factory converted with all good quality bits :)

just bought brand new Exedy 3puk button clutch which is going to be installed on wednesday by Status also with usual 5000km service using motoul oil for both engine and transmission. plus its got everything already done to it. lol

Link to comment
Share on other sites

$350 is toooooo cheap. thats how much im paying for labour to get my clutch changed lol

alot more work is involved. as Wayne mentioned speak to the boys at RE

you also have status tuning also and both work shops are highly recommended.

There isn't much difference in labour between doing a clutch and a manual conversion. You still have to drop the box and refit and refit the clutch, you're just refitting a different box. The difference is mainly fitting the pedal box, master cylinder and clutch line.

Link to comment
Share on other sites

Sounds alright, but I still think paying 18k for a manual GTT is better of paying 14+4k for a manual converted GTT.

What would you do if you were me? :P

Original manual GTT. No contest. Not only will you be getting a car that was designed from the factory to be manual, you should be able to get a better car in other respects as well for the 4k premium.

Link to comment
Share on other sites

honestly, rather have bought a manual r34 than to go through it. its just i put in a too much into the car to start all over. best bet to buy a manual r34. be sure to check it though. searching for an r34 ages ago myself, most were auto thats been converted to manual anyways (either once landed here or been done in japan)

Link to comment
Share on other sites

Original manual GTT. No contest. Not only will you be getting a car that was designed from the factory to be manual, you should be able to get a better car in other respects as well for the 4k premium.

Yeah, that's what I'm thinking of doing, just wait it out and not rush it, until I can find a manual one that I like :P

honestly, rather have bought a manual r34 than to go through it. its just i put in a too much into the car to start all over. best bet to buy a manual r34. be sure to check it though. searching for an r34 ages ago myself, most were auto thats been converted to manual anyways (either once landed here or been done in japan)

How would I actually check if it's been converted or not? Like what if they used ALL R34 manual parts for conversion? Including dash and all?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
    • Nah, im after the more newer looking, one with the OLED display
    • We revised the neutral wire instructions. The old way was wrong.  R34 gearbox change.pdf
×
×
  • Create New...